Fire hydrant C9+ Traffic DN100 - Symmetric nozzles - Belgium version
SAINT-GOBAIN PAM fire hydrants are fire safety devices designed for use on a water network or reservoir in all types of environments. Engineered to be accessible and easy to locate, they enable rapid and effective intervention in the event of a fire.
Description
,
- Operating square 30x30
- Straight box
- Automatic drainage
- Nozzles : Two symmetrical side nozzles and one symmetrical front nozzle, or one symmetrical front nozzle.
Technical design
| 100 | Straight box | 2xDN65 + 1xDN100 | 1066 | 2015 | 584 | 478 | 1235 | 152 | 100x90 | 110.5 | 298117 |
Features
Field of use
Fire hydrants pillar or underground type are designed, according to applicable standards and regulations, for exclusive use of fire protection and using drinking water or raw water network.
They must be handled and used in strict compliance with the recommendations and best practice by personnel trained with these recommendations.
These devices must be inspected periodically (as required by regulations or recommended instructions) to verify and maintain their proper and safe operation.
A reliable long term choice
SG PAM fire hydrants are designed to offer a long service life without requiring specific maintenance; their functionality remains intact even after many years of use.
The products, in fact, deliver performance levels that exceed standard requirements, in full compliance with NF regulations :
- an opening and closing cycle count far beyond the required 1,000 cycles
- a shell pressure resistance greater than 25 bar
- easy operation with torque values below 80 Nm
- a body made entirely of ductile iron, providing high safety factors capable of withstanding both accidental impacts and network operating disturbances, including water hammer
- a minimum torque resistance to external forces of 250 Nm
- for improved corrosion resistance, the PI is fully coated inside and outside with a thick epoxy powder layer (250 microns in the standard version, 300 microns in the reinforced version)
- an additional coating on the above ground section enables it to withstand climatic stresses such as sun, moonlight, and adverse weather conditions
Ease of installation and commissioning
Traffic version (VR) :
By simply loosening the four bolts connecting the above ground section of the hydrant to its buried base (junction within the ground module). This makes it very easy to comply with installation standard NF S 62 200, which requires that the hydrant outlets always be oriented toward the access route used by fire fighting vehicles.
During installation, to correctly orient the outlets in relation to the sidewalk, or in the event of environmental changes such as the construction of new buildings, no excavation is required. SG PAM fire hydrants can be rotated through 360°, one degree at a time.
Material and coatings
| Item | Designation | Material | Coating |
|---|---|---|---|
|
1 |
1a - Operating square |
Ductile iron EN GJS 400 15 or EN GJS 500 7, EN 1563 | Dacromet + Polyurethane blue20 µm |
| 1c - Nozzles body | Ductile iron EN GJS 400 15 or EN GJS 500 7, EN 1563 | REI: 250 µm powder epoxy + blue RAL 5005 polyurethane | |
| 1d - Extension Tube | Ductile iron EN GJS 400 15 or EN GJS 500 7, EN 1563 | REI: 250 µm powder epoxy coating | |
| 1e - Valve box | Ductile iron EN GJS 400 15 or EN GJS 500 7, EN 1563 | REI: 250 µm powder epoxy coating | |
| 1f – Lower barrel | Ductile iron EN GJS 400 15 or EN GJS 500 7, EN 1563 | REI: 250 µm powder epoxy + blue RAL 5005 polyurethane | |
| 1g – Screwed box | Ductile iron EN GJS 400 15 or EN GJS 500 7, EN 1563 | REI: 250 µm powder epoxy coating | |
| 1h – Duckfoot bend | Ductile iron EN GJS 400 15 or EN GJS 500 7, EN 1563 | REI: 250 µm powder epoxy coating | |
| 1b- Marking cover |
ABS |
Polyurethane blue RAL 5005 |
|
|
2 |
Screwed bearing |
Brass type CuZn39Pb2, EN 12164 | |
|
3 |
Operating screw |
Steel grade X20Cr13, EN 10088 3 | |
|
4 |
Operating nut |
Brass type CuZn39Pb2, EN 12164 | |
|
5 |
Fixing screw |
Steel grade 8/8 | Zinc plated, yellow passivated |
|
6 |
Operating tube | Steel grade Tu 56 B |
Galvanized |
|
7 |
Valve |
Ductile iron EN GJS 400 15 or EN GJS 500 7, EN 1563 |
EPDM overmolding |
|
8 |
Nozzles |
Depending on models | |
| 9 | Control shaft | Steel grade X20 Cr 13 EN 10088-1 | |
| 10 | Crimp pin | Steel grade X20 Cr 13 EN 10088-1 | |
| 11 | Control shaft | Forged steel C35 - NF EN 10083-1 | Black cataphoretic coating, 25 microns thick |
| 12 | Fasteners | Steel grade 8/8 | Zinc plated, yellow passivated |
| 13 | Cales de renversabilité | Ductile iron GS | Blue powder epoxy, 250 µm + Blue polyurethane, RAL 5005 |
Installation guide NPPI 01 F
